WHAT IS A PING SWEEP
In networking and reconnaissance, a ping sweep is a network scanning method that can establish a range of IP addresses that map to live hosts. The most used tool to run a ping sweeps is fping, which traditionally was accompanied by gping to generate the list of hosts for large subnets, although the more recent version of fping includes that functionality.
Ping Sweep is also known as ICMP sweep. You can use fping command for ping sweep. This command is a ping-like program which uses the Internet Control Message Protocol (ICMP) echo request to determine if a host is up. fping is different from ping in that you can specify any number of hosts on the command line, or specify a file containing the lists of hosts to ping. If a host does not respond within a certain time limit and/or retry limit, it will be considered unreachable.
HOW TO INSTALL FPING
Ubuntu / Debian and other derived distribution
sudo apt install fping
Redhat / Centos and other derived distribution
In .rpm distributions we can install fping from the source file using the below commands.
cd /tmp/ wget http://fping.org/dist/fping-4.2.tar.gz tar -xvzf fping-4.2.tar.gz cd fping-4.2/ ./configure make && make install
Or if you want fping to support IPv6 addresses follow next steps
./configure --prefix=/usr/local --enable-ipv4 --enable-ipv6 make && make install
HOW TO USE FPING
Check the current fping version
fping: Version 4.0 fping: comments to email@example.com
Ping Multiple hosts from command line
fping 192.168.1.1 192.168.1.102 localhost 126.96.36.199 188.8.131.52
192.168.1.1 is alive 192.168.1.102 is alive localhost is alive 184.108.40.206 is alive 220.127.116.11 is alive
Ping Multiple hosts using file
fping < file.txt 192.168.1.1 is alive 192.168.1.102 is alive 192.168.1.150 is unreachable localhost is alive 192.168.147.2 is alive 18.104.22.168 is alive 22.214.171.124 is alive
Ping IPs range from command line
fping -s -g 192.168.1.1 192.168.1.255
192.168.1.1 is alive 192.168.1.102 is alive ICMP Host Unreachable from 192.168.1.102 for ICMP Echo sent to 192.168.1.2 ICMP Host Unreachable from 192.168.1.102 for ICMP Echo sent to 192.168.1.3 ICMP Host Unreachable from 192.168.1.102 for ICMP Echo sent to 192.168.1.4 ICMP Host Unreachable from 192.168.1.102 for ICMP Echo sent to 192.168.1.5 [...] 192.168.1.1 is unreachable 192.168.1.2 is unreachable 192.168.1.3 is unreachable 192.168.1.4 is unreachable 192.168.1.5 is unreachable [...] 255 targets 2 alive 253 unreachable 0 unknown addresses 253 timeouts (waiting for a response) 1014 ICMP Echos sent 2 ICMP Echo Replies received 1008 other ICMP received 0.05 ms (min round trip time) 1.71 ms (avg round trip time) 3.37 ms (max round trip time) 12.003 sec (elapsed real time)
Ping a complete Network
Using the below command you can ping a complete network once using the option (-r 1) within the parameters. As you can easily understand you can increase this value according to your specific needs.
fping -g -r 1 192.168.0.0/24
HOW TO BLOCK PING SWEEPS ?
Port scans and ping sweeps cannot be blocked without taking the risk to compromise the network capabilities. However, it's possible to block such requests without any difficulties at host levels. Ping sweeps can be stopped if ICMP echo and echo-reply are turned off.
Blocking Ping Sweeps on Linux System
If you are using any Linux environment along with iptables you can easily block ping sweeps on every machine connected on the network adding into your iptables configuration the following rule:
iptables -A OUTPUT -p icmp --icmp-type echo-request -j DROP
Blocking Ping Sweeps on Windows System
On Windows machine it's also very easy to block ping sweeps but it's a little bit longer.
- Log into Windows using an administrator-level account.
- Press and hold the Windows key (located between the Ctrl and Alt keys) and the "R" key.
- Type "wf.msc" in the box (no quotation marks), and press "Enter."
- Right-click the "inbound rules" link in the left pane, and then click "New rule" from the context menu.
- Select the "Custom" radio button, and click "Next."
- Select "All Programs" and click "Next."
- Choose ICMPv4 as your protocol type, and click "Next."
- Click the "Customize" button.
- Choose "echo request" as the "Specific ICMP type."
Important: If you have enabled port forwarding, make sure that TCP port 445 is closed. Otherwise, the pings will still get through.